ANSI/CEMA 102-2022

Conveyor Terms and Definitions

This standard lists and defines over 1,500 terms applying to conveyors, conveyor systems, and allied equipment.

CEMA 705-2021

Conveyor Performance Terminology

A compilation of definitions for terms used in the conveyor industry

ANSI B77.1-2022

Passenger Ropeways - Aerial Tramways, Aerial Lifts, Surface Lifts, Tows and Conveyors - Safety Requirements

This document establishes a standard for the design, manufacture, construction, operation, and maintenance of passenger ropeways. For this standard, passenger ropeway categories include: aerial tramways (single and double reversible); aerial lifts (detachable lifts, chair lifts, and similar equipment); surface lifts (T-bar lifts, J-bar lifts, platter lifts, and similar equipment); tows (wire rope and fiber rope tows); and conveyors.

ISO/TR 16764:2003

Lifts, escalators and passenger conveyors -- Comparison of worldwide standards on electromagnetic interference/electromagnetic compatibility

ISO/TR 16764:2003 consists of a comparison of electromagnetic interference/electromagnetic compatibility (EMI/EMC) worldwide standards of interest to the lift industry.

ASTM D7204-23

Standard Practice for Sampling Waste Streams on Conveyors

1.1 This practice describes standard procedures for sampling waste on open and closed conveying systems and is applicable to any waste material that can be conveyed to a waste pile or container. The conveyor system can be a vertical (vertical lifts), sloped, or horizontal type. 1.2 This practice is intended for particles and slurries, which can be sampled using scoop, dipper, or shovel type samplers. 1.3 The practice is not intended for large size sample constituents, such as boulders, large rocks, and debris. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ISO 3963:1977

Fertilizers - Sampling from a conveyor by stopping the belt

The method should be used only where other methods, such as automatic sampling of scoop sampling from a free fall, are impossible, or as a reference method.It consists in inserting of two parallel boards or metal sheets vertically down into and at right angles to the streams of the material and to the axis of the stopped belt, and removing of the material between the boards or sheets.

MIL-C-23218C

Conveyor, Vertical, Tray Type, 100 Pound Package Tray Capacity (Shipboard Use)

This specification covers powered, tray type, vertical conveyors used for handling packages up to 100 pounds on board Naval ships.

MIL-C-23842B

Conveyor, Vertical, Tray Type, for 3000 Pound Palletized Loads (Shipboard use)

This specification covers powered tray type vertical conveyors used to move palletized loads up to 3000 pounds aboard Naval ships. Only one classification of conveyors is covered by this specification.

ANSI/CEMA 405-2003 (R2020)

Slat Conveyors

This standard, fifth in the series pertaining to unit handling conveyors, proposes certain minimum standards for use in the design and application of slat conveyors.

ANSI/CEMA B105.1-2021

Specifications for Welded Steel Conveyor Pulleys with Compression Type Hubs

This publication provides recommended load ratings, dimensional information, and criteria for selection of welded steel conveyor pulleys. With Metric Conversion.

ISO 2406:1974

Continuous mechanical handling equipment - Mobile and portable conveyors - Constructional specifications

Specifies the dimensional characteristics of mobile and portable conveyors.

ISO 5710:1980

Equipment for internal farm work and husbandry - Continuous manure scraper conveyors for stalls

Specifies requirements for the characteristics, dimensions, methods of installation and safety of closed- circuit conveyors. Applies to evacuation devices fitted with scrapers, moving continuously in a closed circuit, inteded to remove solid and liquid manure collected in non- grid covered channels in enclosed stalls. It applies to elevators only in so far as these from part of the circuit.

ISO 9851:1990

Continuous mechanical handling equipment - Overhead electrical monorail conveyors - Definitions and safety rules

Defines basic terms and specifies safety rules for overhead electrical monorails for materials handling, including the tracks, supporting structure, lifting and lowering devices, the trolleys and the load-supporting devices. Does not apply to systems driven by hand or by gravity, or to systems for conveying people.

SAE ARP 1836C-2016 (SAE ARP1836C-2016)

Aircraft Cargo Conveyor

ISO 2140:1975

Continuous mechanical handling equipment for loose bulk materials - Apron conveyors

Specifies the main dimensions concerning the construction of apron conveyors, namely pitch of chain, width of apron, height of cheek plates. Practical examples are also given.

ISO 7189:1983

Continuous mechanical handling equipment - Apron conveyors - Design rules

Establishes design rules for apron conveyors used for the transport of both loose bulks materials and unit loads.