PDF Price
$0.00
These voluntary consensus maritime standards relate to OSHA maritime standards - 1915, 1917, and 1918 standards and detail topics such as foot protection, toe caps, and portable reinforced plastic.
The purpose of this standard is to provide reasonable safety for life, limb, and property. In order to develop an effective safety program, the standard may serve also as a basis for purchase requirements and for instructions in personnel training, and in the preparation of motivational/ instructional material such as safety practices, manuals, posters, and the like. This standard is also intended to provide the manufacturer, purchaser, and user of metal ladders with a set of performance and dimensional requirements against which a product may be compared. It is not the purpose of this standard to specify all the details of construction of portable metal ladders. The limitations imposed are for the purpose of providing adequate general requirements and testing methods needed for consistency.
This standard prescribes minimum requirements for the design, construction, and use of fixed ladders, and sets forth requirements for cages, wells, and ladder safety systems used with fixed ladders, in order to minimize personal injuries. All parts and appurtenances necessary for a safe and efficient ladder shall be considered integral parts of the design.
The purpose of this standard is to provide reasonable safety for life, limb, and property. In order to develop an effective safety program, the standard may serve also as a basis for purchase requirements and for instructions in personnel training, and in the preparation of motivational/instructional material such as safety practices, manuals, posters, and the like. This standard is also intended to provide the manufacturer, purchaser, and user of reinforced plastic ladders with a set of performance and dimensional requirements against which a product may be compared. It is not the purpose of this standard to specify all the details of construction of portable reinforced plastic ladders. The limitations imposed are for the purpose of providing adequate general requirements and testing methods needed for consistency.
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury. 1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards. 1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards that can potentially result in injury. 1.2 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. 1.3 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed. 1.4 Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this standard rendering the ASTM marking invalid. 1.5 This specification is not applicable to overshoes with safety toe caps or strap on devices with safety toes. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ANSI/ISEA Z308.1-2015 establishes minimum performance requirements for first aid kits and their supplies that are intended for use in various work environments. Classification of first aid kits, designating the assortment of items and quantity of each item, is based on the anticipated number of users intended to be served by each first aid kit, as well as the complexity of the work environment and level of hazards. First aid kit containers are classified by portability, ability to be mounted, resistance to water and corrosion and impact resistance.
This standard sets forth criteria related to the general requirements, testing, permanent marking, selection, care, and use of protectors to minimize the occurrence and severity or prevention of injuries from such hazards as impact, non-ionizing radiation and liquid splash exposures in occupational and educational environments including, but not limited to, machinery operations, material welding and cutting, chemical handling, and assembly operations. Certain hazardous exposures are not covered in this standard. These include, but are not limited to: Bloodborne pathogens, X-rays, high energy particulate radiation, microwaves, radio-frequency radiation lasers, masers, and sports and recreation.
This standard describes Types and Classes, testing and performance requirements for protective helmets. These include recommended safety requirements for authorities considering the establishment of regulations or codes concerning the use of protective helmets.