Miscellaneous rivet standards from ISO, SAE, ASTM, and others
This standard covers general and dimensional data for those types of metric small solid rivets recognized as American National Standard. Included is an appendix covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of a product, the dimensions in the tables shall govern over recalculation by formula.
This Standard covers general and dimensional data for those types of small solid rivets recognized as American National Standard. All other types of small solid rivets, within the limits of the diameters contained herein, are to be considered special. Also included is an appendix covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.
This Standard covers general and dimensional data for those types of large solid rivets recognized as American National Standard together with dimensional data applicable to manufactured heads after driving, driven heads, and hold-on (dolly bar) and rivet set impressions. Also included are appendixes covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.
This International Standard specifies two series of shank diameters of rivets for general use, except blind rivets, in the range from 1 mm up to and including 36 mm.
This standard covers complete general and dimensional data for semi-tubular rivets, full tubular rivets, split and rivet caps for use in general purpose applications. The products described are suitable for joining metallic and non-metallic materials or combinations thereof. It should be noted that while these products are suitable for general purpose assembly, other special purpose types are available to satisfy particular requirements and manufacturers should be consulted for special requirements. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning availability of products.
1.1 This specification covers structural steel plates, shapes, and bars intended primarily for use in ship construction. 1.2 Material under this specification is available in the following categories: 1.2.1 Ordinary Strength Grades A, B, D, and E with a specified minimum yield point of 34 ksi [235 MPa], and 1.2.2 Higher Strength Grades AH, DH, EH, and FH with a specified minimum yield point of 46 ksi [315 MPa], 51 ksi [350 MPa], or 57 ksi [390 MPa]. 1.3 Shapes and bars are normally available as Grades A, B, AH32, and AH36. Other grades may be furnished by agreement between the purchaser and the manufacturer. 1.4 The maximum thickness of products furnished under this specification is 4 in. [100 mm] for plates and 2 in. [50 mm] for shapes and bars. 1.5 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.6 Units This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This specification 2 covers steel rivets for use in boilers and pressure vessels and steel bars for use in the manufacture of rivets. 1.2 Two grades are covered: 1.2.1 Grade A— Bars having a yield point of 23 000 psi (160 MPa) minimum with carbon 0.18 % maximum. 1.2.2 Grade B— Bars having a yield point of 29 000 psi (200 MPa) minimum with carbon 0.28 % maximum. 1.2.3 Rivets are manufactured from the applicable bar grade. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This specification covers three grades of steel rivets in diameters from 1 / 2 to 1 1 / 2 in. inclusive, for structural fabricating purposes. The grades are as follows:... 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.1 This specification covers wire and rod in the alloys ( Note 1 ) shown in Table 1 and the tempers shown in Table 2 [Table 3] and Table 4 [Table 5], suitable for manufacturing rivets and other similar items by cold-heading operations. Note 1: Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For rolled or cold-finished wire and rod, see Specification B211 , and for extruded wire and rod, see Specification B221 . 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527 . 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2 . 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 The SI units are shown either in brackets or in separate tables. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This test method covers the double shear testing of aluminum and aluminum alloy rivets with round, solid shanks and cold-heading wire and rod. 2 Note 1: Exceptions to this test method may be necessary in individual specifications or methods for tests for a particular material. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard specifies the dimensions of semitubular rivet and bolts for brake linings/blocks.