Testing/Measurement

Whether you work with hydro, wind, thermal, or alternative power generation; power generators; low voltage or high voltage distribution; power distribution racks or cables; smart grid or ensuring workplace safety, the power industry has a strong focus on standardization and interoperability. This list on Testing/Measurement includes standards from ISO, IEC, IEEE, and others.

IEEE 1366-2012

IEEE Guide for Electric Power Distribution Reliability Indices

Distribution reliability indices and factors that affect their calculations are defined in this guide. The indices are intended to apply to distribution systems, substations, circuits, and defined regions.

IEEE 1515-2000 (R2008)

IEEE Recommended Practice for Electronic Power Subsystems: Parameter Definitions, Test Conditions, and Test Methods

This recommended practice defines many common parameters for ac-dc and dc-dc electronic power distribution components and subsystems. This enables electronic system engineers, manufacturers, and researchers to speak with a common language and hence facilitates effective and efficient communications. Furthermore, implementation of a common specification language will allow the power electronics industry as well as the user communities, including government system developers, to acquire cost and time-effective electronic power subsystems with significantly enhanced interchangeability.

IEEE Std 1656-2010

IEEE Guide for Testing the Electrical, Mechanical, and Durability Performance of Wildlife Protective Devices on Overhead Power Distribution Systems Rated up to 38 kV

This guide is applicable to wildlife protective products installed on overhead electrical distribution systems rated up to and including 38 kV. Test recommendations regarding these products that are in direct contact or in the proximity of energized parts and conductors are provided in this guide.

IEC 62129-1 Ed. 1.0 b:2016

Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers

IEC 62129-1:2016 specifies procedures for calibrating an optical spectrum analyzer that is developed for use in fibre-optic communications and designed to measure the power distribution of an optical spectrum. It does not apply to an optical wavelength meter that measures only centre wavelengths, a Fabry-Perot interferometer or a monochromator that has no display unit. This first edition of IEC 62129-1 cancels and replaces the first edition of IEC 62129, published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - update of term and definitions; - update of calibration conditions; - calculation change of uncertainties related to wavelength temperature dependence, power linearity, power level temperature dependence; - move of Annex E to the bibliography. Keywords: calibrating an optical spectrum analyser

ASTM E2022-16(2021)

Standard Practice for Calculation of Weighting Factors for Tristimulus Integration

1.1 This practice describes the method to be used for calculating tables of weighting factors for tristimulus integration using custom spectral power distributions of illuminants or sources, or custom color-matching functions. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM G178-16

Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique

1.1 This practice describes the determination of the relative actinic effects of individual spectral bands of an exposure source on a material. The activation spectrum is specific to the light source to which the material is exposed to obtain the activation spectrum. A light source with a different spectral power distribution will produce a different activation spectrum. 1.2 This practice describes two procedures for determining an activation spectrum. One uses sharp cut-on UV/visible transmitting filters and the other uses a spectrograph to determine the relative degradation caused by individual spectral regions. 1.3 The techniques are applicable to determination of the spectral effects of solar radiation and laboratory accelerated test devices on a material. They are described for the UV region, but can be extended into the visible region using different cut-on filters and appropriate spectrographs. 1.4 The techniques are applicable to a variety of materials, both transparent and opaque, including plastics, paints, inks, textiles and others. 1.5 The optical and/or physical property changes in a material can be determined by various appropriate methods. The methods of evaluation are beyond the scope of this practice. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

IEC/TS 61967-3 Ed. 2.0 b:2014

Integrated circuits - Measurement of electromagnetic emissions - Part 3: Measurement of radiated emissions - Surface scan method

IEC TS 61967-3:2014 provides a test procedure which defines an evaluation method for the near electric, magnetic or electromagnetic field components at or near the surface of an integrated circuit (IC). This diagnostic procedure is intended for IC architectural analysis such as floor planning and power distribution optimization. This test procedure is applicable to measurements on an IC mounted on any circuit board that is accessible to the scanning probe. In some cases it is useful to scan not only the IC but also its environment. For comparison of surface scan emissions between different ICs, the standardized test board defined in IEC 61967-1 should be used. This measurement method provides a mapping of the electric or magnetic near-field emissions over the IC. The resolution of the measurement is determined by the capability of the measurement probe and the precision of the probe-positioning system. This method is intended for use up to 6 GHz. Extending the upper limit of frequency is possible with existing probe technology but is beyond the scope of this specification. Measurements may be carried out in the frequency domain or in the time domain. This edition includes the following significant technical changes with respect to the previous edition: a) Removal of: Clause 9.4 Data analysis and Annex D Analysing the data from near-field surface scanning; b) Addition of: Introduction, Clause 9.4 Measurement data, Clause 9.5 Post-processing, Clause 9.6 Data exchange and Annex D Coordinate systems; c) Expansion of: Clause 8.4 Test technique and Annex A Calibration of near-field probes.

AMCA 802-19

Industrial Process/Power Generation Fans: Establishing Performance Using Laboratory Models

AMCA Publication 802, Industrial Process/Power Generation Fans: Establishing Performance Using Laboratory Models, has been revised. The new designation on the title page is AMCA Publication 802-19.

ISO 16587:2004

Mechanical vibration and shock - Performance parameters for condition monitoring of structures

ISO 16587:2004 describes the performance parameters for assessing the condition of structures, including types of measurement, factors for setting acceptable performance limits, data acquisition parameters for constructing uniform databases, and internationally accepted measurement guidance (e.g. terminology, transducer calibration, transducer mounting and approved transfer function techniques). The procedures relate to in-service monitoring of structures, and include all components and sub-assemblies necessary to provide the functioning of the structure as a complete entity. The monitoring is intended to be ongoing in nature through the lifecycle of the structure. The target industries for ISO 16587:2004 include: construction, infrastructure, transportation, power generation, oil and gas, and leisure and entertainment. ISO 16587:2004 is applicable to stationary structures, such as: buildings, bridges and tunnels, towers, masts and antennae, tanks and silos, retaining walls and dams, jetties and other shore-side structures, offshore platforms, pressure vessels, and pipelines. Non-stationary structures (e.g. self-propelled ships) and mobile structures (e.g. offshore jack-up platforms) are excluded from ISO 16587:2004.

ASTM D5463-18

Standard Guide for Use of Test Kits to Measure Inorganic Constituents in Water

1.1 This guide covers general considerations for the use of test kits for quantitative determination of analytes in water and wastewater. Test kits are available from various manufacturers for the determination of a wide variety of analytes in drinking water, surface or ground waters, domestic and industrial feedwaters and wastes, and water used in power generation and steam raising. See Table 1 for a listing of some of the types of kits that are available for various inorganic analytes in water. 2 (A) Kit Methodology: A = appearance/turbidity, C = visual colorimetric, GNG = go no go, P = photometric, and T = titrimetric. 1.2 Ranges, detection limits, sensitivity, accuracy, and susceptibility to interferences vary from kit to kit, depending on the methodology selected by the manufacturer. In some cases, kits are designed to replicate exactly an official test method of a standard-setting organization such as the Association of Official Analytical Chemists (AOAC), American Public Health Association (APHA), ASTM, or the U.S. Environmental Protection Agency (USEPA). In other cases, minor modifications of official test methods are made for various reasons, such as to improve performance, operator convenience, or ease of use. Adjustments may be made to sample size, reagent volumes and concentrations, timing, and details of the analytical finish. In yet other cases, major changes may be made to the official test method, such as the omission of analytical steps, change of the analytical finish, omission of reagents, or substitution of one reagent for another. Reagents in test kits are often combined to obtain a fewer number and make the test easier to use. Additives may also be used to minimize interferences and to make the reagent more stable with time. A kit test method may be based on a completely different technology, not approved by any official or standard-setting organization. Combinations of test kits multi-parameter test kits may be packaged to satisfy the requirements of a particular application conveniently. The test kits in such combination products may be used to make dozens of determinations of several parameters. 1.3 Test kit reagent refills are commonly available from manufacturers. Refills permit cost savings through reuse of the major test kit components. 1.4 Because of the wide differences among kits and methodologies for different analytes, universal instructions cannot be provided. Instead, the user should follow the instructions provided by the manufacturer of a particular kit. 1.5 A test kit or kit component should not be used after the manufacturer's expiration date; it is the user's responsibility to determine that the performance is satisfactory. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 10 . 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.